Over twenty years ago, Ponsness/Warren developed a special, moisture resistant, non-petroleum lubricant, called STOS. Quickly everyone realized that STOS was the best all-around grease on the market. Ponsness/Warren applies STOS on every reloader they build to ensure long-lasting, friction-free performance. STOS is ideal for machining equipment, firearms, case re-sizing, fishing reels, automotive parts, gear and cam surfaces, or anywhere that requires lubrication.
Available in 2 handy containers:
2oz Wide Mouth Jar –  A handy, 2 ounce, wide mouth jar, small enough to be carried in your shooting bag or tool box. 
Pin-Point Applicator –  This applicator is filled with our special STOS grease. It¹s equipped with a one inch, hollow, steel tip for those hard-to-reach places. Ideal for trigger assemblies, fishing reels, household needs, etc. 
Penx Pin-Point Applicator – A special oil, which is used by Ponsness/Warren for the prevention of rust and corrosion. Perfect for guns or any other metal surfaces which may be subject to rusting.  
To Order, Click on the Item Number.

 Top

Shot and Powder Measure Kits

Each time you change to a different type or lot of powder, it is very important to check the drop.  These kits allow for the measuring of either shot or powder without interrupting the reloading operation. Available in a four gauge kit or individually.
To Order, Click on the Item Number.

Shot and Powder Bushing Kits

These kits consist of the ten most widely used bushings in clay target shooting.  Bushings are packaged in a foam lined, clear container – allowing for easy identifications and storage.
Click here to view Ponsness/Warren Powder Bushing Charts.
To Order, Click on the Item Number.

To Order, individual Standard Lead Shot Bushings click on the item number.

To Order, individual Powder Bushings click on the item number.

To Order, click on the item number.

Top

Primer Tray Extension Kit

Sliding this extension kit over our existing primer tray, gives you the capacity of 300 primers.  Complete with see through primer tray cover.  
To Order, click on the item number.

Primer Swing Tray Cover

The swing tray cover gives you quick and easy access to the primer tray. Simply loosen wing nut and this tray will swing to the left, allowing primer tray to be filled quickly. Installs in minutes.
To Order, click on the item number.

Wad Guide Fingers

Special wad guide fingers ensure longer life, allow more spring action, and accommodate all style of wads.  
To Order, click on the item number.

Thumb Screw Set

Standard on all new machines, these thumb screws are a must on 800 series reloaders. Replace the four existing top plate screws with these thumb screws, allowing for quicker access when changing bushings, or cleaning shot and powder gears.  
To Order, click on the item number.

Die Cleaning Rod

Works like the Die Cleaning Bracket on new machines. Screws into the bottom of tool head.  
To Order, click on the item number.

Die Cleaning Bracket, Brush and Swab

It is very important that you keep the inside of the resizing dies free of carbon and plastic buildup.  This cleaning bracket quickly attaches to the front of the reloader and by using either the brush or swab, automatically cleans your dies while reloading. Recommended to be used on all 900 and 800 series machines.  
To Order, click on the item number.

Top

Update your older reloader with this Die Removal System. This system allows you to easily remove shells during the reloading process for checking shot or powder weights, inspecting shells, etc. Lift a die pin and slide out the shell - it’s that easy! The cylinder is made of “grivory,” a new compound designed to be stronger and more rigid than aluminum. This new Die Removal Cylinder is built taller, making it much easier to place it in the neutral position. It is so strong that Ponsness/Warren gives it a lifetime warranty against any type of wear.

Conversion Kits

Steel Shot Conversion Kit

To keep up with the changing times, this conversion kit allows you to convert any 950, 900 or 800 series machine to reload steel or bismuth shot. Simply install the patented “Uni-Drop” top plate and the fully adjustable wad ram and you will be ready to remanufacture non-toxic shotshells.
Specify Machine Model.  
To Order, click on the item number.

L/S-1000 3-1/2” Conversion Kit

This kit allows you to reload those expensive 12 gauge magnum goose loads for about the same price as regular field shells. Installs in minutes.  
To Order, click on the item number.

950 Elite Conversion Kit

Converts your 900 Elite into a 950 Elite. Kit includes shell holders, depriming/resizing assembly, final crimp assembly and a new shell seating post assembly. Available in 12GA only.
To Order, click on the item number.

DU-O-MATIC 375 3” and 3-1/2” Conversion Kits

Reloading magnum shells is made easy with these conversion kits. Simply change the resizing die and crimp starter and you’re ready to go.
Kits are available for C – tapering and B – non-tapering style tooling. 
To Order, click on the item number.